Gysmi 161 Inverter Manual Pdf __TOP__

This key is used to activate or exit the unit from standby mode. Activation of the mode is not possible when the product is in welding condition. Note : When the power is turned on, the product starts in standby mode. Welding process selection buttonThis key is used to select the welding process. Each successive press toggles between the following welding processes: TIG HF /TIG LIFT / MMA. The LED indicates the selected process. Trigger mode selection buttonUse this button to configure how the trigger is used. Each successive press toggles between the following modes: 2T / 4T / 4T LOG. The LED indicates the selected mode. Note : the trigger mode selected by default at machine startup corresponds to the last trigger mde used before the last sleep orshutdown. For more information, refer to the section «Compatible Torches and Trigger Behavior». Selecting processes buttonThis key is used to select the «Sub-process». Each successive press toggles between the following sub-processes: PULSE / SPOT (only in TIG mode) / MMA PULSE (only in MMA mode). The LED indicates the selected process. if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[300,250],'manuals_plus-box-4','ezslot_12',103,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-box-4-0');if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[300,250],'manuals_plus-box-4','ezslot_13',103,'0','1'])};__ez_fad_position('div-gpt-ad-manuals_plus-box-4-0_1');if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[300,250],'manuals_plus-box-4','ezslot_14',103,'0','2'])};__ez_fad_position('div-gpt-ad-manuals_plus-box-4-0_2');.box-4-multi-103{border:none!important;display:block!important;float:none!important;line-height:0;margin-bottom:2px!important;margin-left:auto!important;margin-right:auto!important;margin-top:2px!important;max-width:100%!important;min-height:250px;min-width:300px;padding:0;text-align:center!important}Note : SPOT mode is not accessible in 4T & 4T LOG trigger configuration and in MMA welding mode. MMA PULSE welding mode is not accessible in 4T & 4T LOG trigger configurationNote: the sub-process selected by default at machine startup corresponds to the last sub-process used before the last sleep or shutdown. Main incremental encoderAs default, the incremental encoder allows the adjustment of the welding current.. It is also used to set the values of other para- meters which are then selected via the associated keys. Once the parameter setting has been completed, it is possible to press the key of the parameter that has just been set again so that the incremental encoder is again linked to the current setting. It is also possible to press another key related to another parameter to adjust it. If no action is performed on the HMI for 2 seconds, the incremental encoder is again linked to the welding current setting. « Pre-Gas « buttonThe Pre-Gas adjustment is done by pressing and releasing the Pre-Gas button and then activating the main incremental encoder. Pre-Gas value increases when the incremental encoder is operated clockwise and decreases when it is operated anti-clockwise. Once the setting has been made, it is possible to press and release the Pre-Gas button again to re-link the main incremental encoder to the current setting or to wait for 2 seconds. The setting step is 0.1 sec. The minimum value is 0 sec. and the maxi- mum value is 25 sec. « Post-Gas « buttonThe Post-Gas adjustment is done by pressing and releasing the Post-Gas button and then activating the main incremental encoder. Post-Gas value increases when the incremental encoder is operated clockwise and decreases when it is operated anti- clockwise. Once the setting has been made, it is possible to re-press and release the Pre-Gas pushbutton to re-link the main incremental encoder to the current setting or to wait 2 seconds. The setting step is 0.1 sec. The minimum value is 0 sec. and the maximum value is 25 sec. The default value is 6sec. «Up Slop» or current control buttonThe current ramp-up setting is done by pressing and releasing the current ramp-up button and then by activating the main incremental encoder. Current ramp-up value increases when the incremental encoder is operated clockwise and decreases when it is operated anti-clockwise. Once the setting has been made, it is possible to press and release the current ramp-up button again to re-link the main incremental encoder to the current setting or to wait for 2 seconds. The setting step is 0.1 sec. The minimum value is 0 sec. and the maximum value is 25 sec. The default value is 0sec. In MMA mode, the Hotstart is adjustable between 0 and 100% of the welding current in 5% steps. The default value is 40%. Potentiometer for setting the fading or «Downslope».The «Downslope» potentiometer is used to adjust the value of the current fading (clockwise increment and counterclockwise decrement). The value is visible on the 7-segment display and remains displayed for 2 seconds if an action on the potentiometer is performed. The minimum value is 0 sec. and the maximum value is 20 sec. Cold current control buttonWhen one of the 2 processes «TIG HF» or «TIG LIFT» is selected, the cold current setting button is used to adjust the cold current value only in the «PULSE» configuration. The value can be adjusted between 20% and 80% of the welding current. The incremental step is 1%. The default value is 30%. In MMA mode, the Arc Force is indexed from -10 to +10 (-10 = no Arc Force / -9 to +10 = Arc Force setting possible). The default index value is 0. WELDING WITH RUBBERED ELECTRODE (MMA MODE)CONNECTIONS AND RECOMMENDATIONS

CHOICE OF THE IGNITION TYPETIG HF: non-contact high-frequency ignitionTIG LIFT : Arcing by contact (for environments where HF is not desirable). Place the torch in the welding position above the part (distance of about 2-3 mm between the electrode tip and the part). Press the torch trigger (the arc starts without contact using High Frequency impulsions). The initial welding current circulates, the welding carries on according to the welding cycle.Position the torch nozzle and electrode tip on the part and press the torch button.if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[250,250],'manuals_plus-small-square-2','ezslot_37',717,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-small-square-2-0'); Tilt the torch until a distance of about 2-3 mm separates the tip of the electrode from the part. The arc starts.Put the position back into position to start the welding cycle.Warning: Increasing the length of the torch or earth return cables beyond the maximum length specified by the manufacturer will increase the risk of electric shock.COMPATIBLE TORCHESTORCHES TRIGGER BEHAVIOURFor the 1 button torch, the button is called the «main button».For the 2 buttons torch, the first button is called «main button» and the second button is called «secondary button».

Circuit diagrams of many welding machines available on the market, even if the brands do not match the model numbers, welding machine service manuals. Some models have the same control, driver floors only IGBT, transformer, etc. It was launched in different models by increasing its power. 2b1af7f3a8

Gysmi 161 Inverter Manual Pdf TOP

Subscribe Form